Skip to main content

Clinic Research and Benchmarks

Patient Flow Time Study: Following One Visit Door to Door

How to run a patient flow time study in an Indian clinic: mapping each step from arrival to exit, timing them, finding bottlenecks and redesigning the flow.

Bractis clinic guides · Updated · 4 min read

Short answer

A patient flow time study follows real patients through every step of a clinic visit, from arrival, registration and vitals to consultation, tests, billing, pharmacy and exit, recording the time spent at each step and the waiting in between. It shows where time is lost, which steps add little value, and where queues form. Map the steps, time 20 to 30 visits across different hours, find the biggest waits, change the process, and repeat the study.

What a flow study is

A patient flow study, sometimes called a time and motion study, follows patients through the clinic and records each step and the time it takes. Unlike a waiting time measurement, which looks at one gap, a flow study looks at the whole journey. It often reveals surprises: patients sent back to reception twice, vitals taken in a corridor because the nurse's room is busy, or a ten-minute wait for a printed bill.

This guide gives a method for your own clinic, not benchmark figures from other clinics.

Step 1: map the visit

Walk through a typical visit and list every step. A general OPD might have:

  1. Arrival and queue at reception.
  2. Registration or check-in.
  3. Payment of consultation fee, if taken first.
  4. Wait for vitals.
  5. Vitals by nurse or assistant.
  6. Wait for doctor.
  7. Consultation.
  8. Tests or procedures, with waits.
  9. Return to doctor with results, if needed.
  10. Billing.
  11. Pharmacy or dispensing.
  12. Exit.

Draw it as a simple flow on paper, with arrows. Mark where patients wait, where they move between rooms, and where they repeat a step.

Step 2: time real visits

Choose 20 to 30 patients across different hours and days, including your busiest times. A staff member, or a trainee, notes the time each step starts and ends. Explain to patients that you are timing the process to reduce waits, not watching them. Use visit numbers rather than names on the sheet.

On a narrow screen, scroll the table sideways to see every column.

StepStartEndMinutes
Reception queue
Registration
Wait for vitals
Vitals
Wait for doctor
Consultation
Billing queue
Billing
Pharmacy

Step 3: find the bottleneck

Add up the time spent in each step and each wait across all patients. In most clinics, the waits are much longer than the actual work. The biggest single wait is your bottleneck. Look also for:

  • Steps that could happen at the same time, such as registration while waiting for vitals.
  • Steps that could be removed, such as taking payment twice.
  • Back-and-forth movement between rooms.
  • Steps that depend on one person who is also doing something else.

Step 4: redesign

Discuss findings with reception, nurses and doctors together, because each sees a different part of the flow. Ideas that often help include taking vitals in the waiting area with a portable kit, collecting the full fee once at the end, pre-registering booked patients, a fast lane for report-showing visits, and placing billing and pharmacy next to each other. Choose one or two changes, try them for two weeks, and repeat the study.

Measuring success

Compare the total visit time and the biggest wait before and after. Also ask staff whether the new flow is easier. A change that saves patient time but overloads one staff member will not last.

Special visit types

Flow differs for new patients, follow-ups, report showings, procedures and vaccinations. If one type causes most delays, map it separately. For example, report-showing visits often wait as long as full consultations for a two-minute review.

Privacy and dignity

Do not record diagnoses or names on the study sheet. Make sure the observer does not stand in consultation or examination rooms. Under the DPDP Act, use the data only to improve the clinic, and destroy the sheets after analysis.

Using software data

If your clinic software records check-in, vitals, consultation and billing times, you can run a flow study on months of data without manual timing. Check that staff actually record events when they happen, not later in the day, or the times will be misleading.

A worked example

A paediatric clinic timed 25 visits. The consultation averaged about eight minutes, but total visit time was much longer. The largest waits were before vitals, because one nurse weighed and measured every child in a small room, and at billing, because the fee was collected after the consultation alongside vaccine payments. The clinic trained a receptionist to weigh children in the waiting area and moved routine fee payment to check-in, keeping vaccine billing separate. A repeat study showed shorter total visit times and fewer crowded moments at the counter.

Keeping the gains

Improvements in flow often fade after a few weeks as old habits return or a staff member leaves. Write the new flow on one page and put it at reception and in the nurse's room. Train new staff on it in their first week. Repeat a short flow study of ten visits every quarter to check that waits have not crept back. When the clinic adds a doctor, a service or a new room, map the flow again before the change, because each addition shifts where patients queue. Share results with the team, so staff see the effect of their work.

Common mistakes

  • Timing only the consultation.
  • Studying only quiet hours.
  • Redesigning without asking the staff who do the work.
  • Changing everything at once.
  • Not repeating the study after changes.

Where Bractis fits

Bractis keeps check-in, consultation and billing for each visit together, and payment status is attached to the visit, which makes it easier to see where a visit is stuck. For reports on step times, ask the team what is supported today.

Frequently asked questions

What is a time and motion study in a clinic?

A study that follows patients through each step of a visit and records the time spent on each step and in each wait.

How many patients should I study?

Twenty to thirty visits across busy and quiet hours is usually enough to see the main bottlenecks.

What is the most common bottleneck?

It varies, but waits before the doctor, for vitals, and at billing are common.

Can software replace a manual study?

If it records accurate times for each step, yes. Check that events are recorded as they happen.

Run this in your own clinic

Bractis is clinic management software built for Indian OPDs: appointments, patient records, prescriptions, billing and follow-up in one place. You can try it in your own clinic before you decide.

Sources and review

Written by the Bractis editorial team for doctors and clinic owners in India. Rules, fees and prices change: check the linked primary sources before acting, and ask your CA or lawyer about your own case.